MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

Set screw (grub screw) sizes for T-Mount adapters?
View previous topic :: View next topic  


Reply

Does anyone happen to know the size of screws used in the common generic T-mount adapters? I'm referring to the three little set screws or grub screws around the perimeter, which lock the outer part to the inner ring.

I've checked with one of mine, and an M3 screw (the smallest size stocked by hardware stores) is a bit too big, while an M2 screw (the next smaller size stocked by the specialty electronics store) is too small. Neutral I took my adapter into an RC hobby supply store, and the shopkeeper tried his range of screws only to find that his closest match (M2.5) was also just a touch too small. Neutral

He suggested M2.6, which is apparently a very uncommon but still standard size, but he didn't have any in stock. Searching around, it looks like I would have to order from overseas to get them, or have a local engineering shop procure a box of 100. Shocked


Before I go too far, does anyone know if the size is in fact M2.6? Or perhaps it is even an imperial size? Question

Thanks. Cool


Reply

Seems like a new T2 adapter might cost less than the proper screws, no?


Reply

visualopsins wrote:
Seems like a new T2 adapter might cost less than the proper screws, no?


Pretty close!

But I'm actually after are some longer screws, for some of my lens adaptation projects. Wink


Reply

Google "M2.6" returns:

Is 12mm long enough for you? Very Happy US$4.20 for 10: http://www.microfasteners.com/catalog/products/METSCM.cfm

http://www.modelfixings.co.uk/machine_screws.htm

Threaded Rods is also a possibility.


Reply

visualopsins wrote:
Google "M2.6" returns:

Is 12mm long enough for you? Very Happy US$4.20 for 10: http://www.microfasteners.com/catalog/products/METSCM.cfm

http://www.modelfixings.co.uk/machine_screws.htm

Threaded Rods is also a possibility.


10 SWG is 2.588mm in diameter. Can you find a die?


Reply

Thanks. Yes, there are several options for places to order the screws... I was just hoping to find out what the actual size was first. Wink

I had given some thought to enlarging the holes and making new threads for M3... but then I would be on the hunt for more oddball screws if I ever decided to go back to the flush setscrews. Wink


Reply

martyn_bannister wrote:
visualopsins wrote:
Google "M2.6" returns:

Is 12mm long enough for you? Very Happy US$4.20 for 10: http://www.microfasteners.com/catalog/products/METSCM.cfm

http://www.modelfixings.co.uk/machine_screws.htm

Threaded Rods is also a possibility.


10 SWG is 2.588mm in diameter. Can you find a die?


Here's a die at a reasonable price


Reply

An update - I did manage to find the screws I needed... two sets of them in fact! Surprised

We had an old dead VCR in the garage, and I had intended to take it apart before we threw it out. It turns out that while the majority of the VCR was cheaply made plastic (with snaps and course self-tapping screws), the head mechanism was actually a very high precision part with lots of fine threaded machine screws.




I saved out everything of value, and soon had a small pile of miscellaneous screws & springs, along with a belt, a wheel, and a motor.




But wait... what were these small screws? Could they be the right size? Surprised





So in the end, I have my screws. I still don't know what size they are though. Wink


Reply

You will also find some strong magnets in old VCR's that can be useful.

I have a donut shaped one that I use for holding small screws and parts safely when I'm taking something to bits.

And I wipe my screwdrivers over it to magnetise the tip and hold small screws in place.