MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

Tripod Question: Bolt Size?
View previous topic :: View next topic  


Reply

What is the bolt size that you screw into the camera?

I'm looking to buy bushings so that I can drill, screw in and mount a wooden pinhole camera, but I don't know what the size is.

I see the 1/4 to 3/8 bushings. http://www.bhphotovideo.com/c/product/221118-REG/
But is this a reducer I need for standard tripod mount?

Thanks for any help.


Reply

I think I might have found my answer: http://www.sjdiscounttools.com/hel5521-6.html


Reply

standard 1/4-20 thread, not too long to avoid wrecking camera!


Reply

The modern small thread is 1/4" Whitworth, the older Continental thread is 3/8" Whitworth.
If you have a 1/4" UNC bolt it will go in, but don't force it (or I might be thinking of 6mm).
Don't ask me why the world camera industry settled on an obsolete UK Imperial bolt size, the answer is lost in the mists of time - probably the wide base of installed equipment.


Reply

Thanks!
Off to buy some threads


Reply

Farside wrote:
The modern small thread is 1/4" Whitworth, the older Continental thread is 3/8" Whitworth.
If you have a 1/4" UNC bolt it will go in, but don't force it (or I might be thinking of 6mm).
Don't ask me why the world camera industry settled on an obsolete UK Imperial bolt size, the answer is lost in the mists of time - probably the wide base of installed equipment.


Ok before I purchase... All Tripods and cameras are 1/4-20 as of today? I don't have a way to measure as I'm always at my office.
I just want to be sure I will be ordering the correct helicoil kit/tap.

Thank you guys for your help, I do appreciate it.
-Nate


Reply

Razster wrote:


Ok before I purchase... All Tripods and cameras are 1/4-20 as of today?

Yep, that's the case, to the best of my knowledge. I've never come across any other thread, with the exception of the 3/8 option, which was /is still being used in heavier equipment.


Reply

Razster wrote:
Ok before I purchase... All Tripods and cameras are 1/4-20 as of today?
MOST tripods and cameras use this standard. As Dave mentions, the larger is still in use, but normally with esoteric, heavy, or rather non-mainstream gear. Many high-end tripods still include the 1/4-20 screw as standard, while including the adaptor to also use as 3/8 if needed.


Reply

IIRC most if not all Manfrotto tripods and heads use 3/8" - it's certainly 3/8" on my 055XPROB tripod and MN229 and MN488 heads. Some of the older Exaktas and the Mamiya RB67 also used 3/8" although in the case of those and Manfrotto heads, you can use a 3/8" male-1/4" female reducer.


Reply

It's the quick-release plate, really, not the tripod. I don't know if different size screws are available in standard plates, it would be an easy option for manufacturers.


Reply

The Manfrotto 030 hex QR plates come in both 1/4" and 3/8" versions - there's also a large square version of the 030 plate for the more well endowed camera: http://tinyurl.com/QR-plate

I don't know if their other QR plates have dual thread options though.

Speaking as a user, not a seller, of their stuff... Laughing


Reply

Found something that states it well - http://www.enginehistory.org/british_fasteners.htm
So, 1/4" UNC will fit, no problem, but the thread angle is not the same as BSW, which is relatively unimportant in this application. The warning of doom below applies to safety-important fastenings, not camera tripods.
On the other hand; if the tripod fastening is being used a lot, premature wear of the thread might result. Your call.
It's still possible to get BSW fasteners if you look for them.

"Another area that causes confusion is the fact that some BSW or BSF nuts can be screwed on UNF or UNC bolts and vice-versa. Under NO circumstances should this practice even be considered. Most of the coarse threads share the same threads per inch which means BSW nuts can be screwed onto UNC bolts and vice-versa. The exception to this being ½ inch -- ½ inch BSW is 12 threads per inch and ½ inch UNC is 13 threads per inch. Again, it must be emphasized that this practice should not be a consideration. Whitworth and UNC/UNF thread forms differ greatly, the primarily one being the thread angle (see illustrations). BSW and BSF feature a 55 degree thread angle (47 ½ degrees for BA) and UNC/UNF threads feature a 60 degree thread angle. Consequently, if these fasteners are interchanged, considerable loss of holding force, fatigue resistance and strength will result. Unfortunately, this author has seen examples of mechanics -- unaware the these subtleties -- mixing fasteners at will -- gee, if it screws on it must be okay..!! (Scary thought).


Reply

Nate,

Razster wrote:
What is the bolt size that you screw into the camera?

I'm looking to buy bushings so that I can drill, screw in and mount a wooden pinhole camera, but I don't know what the size is.

I see the 1/4 to 3/8 bushings. http://www.bhphotovideo.com/c/product/221118-REG/
But is this a reducer I need for standard tripod mount?

Thanks for any help.


If you are building a wooden camera from scratch get "T-nuts" with the 1/4 Whitworth thread.

A T-nut is a threaded sleeve into which the screw fits, and it has an integral flange at the end, and the flange has four spikes for stopping it from rotating.

So, on the base plate you drill a hole that allows the "sleeve" to go right through, and use an auger bit the same diameter of the flange to make a recess for the flange to sit in. Make sure that when the T-nut is fitted, its end just falls short of being flush with the base surface. Use a small drill to drill holes for the spikes to locate themselves. Of course, you would need to add another piece of material on top of the T-nut to stop it from falling into the camera.

The Bender self-assembly large format camera kit includes such T-nuts but I get them from the local hardware store without trouble.