| View previous topic :: View next topic |
| Author |
Message |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Thu Mar 08, 2012 9:17 pm Post subject: How to change infinity on Samyang 35/1.4 |
|
 Posted: Thu Mar 08, 2012 9:17 pm Post subject: How to change infinity on Samyang 35/1.4 |
|
|
pholler wrote:
Hey guys,
i recently bought the Samyang 35/1.4 and it has got an infinity focus misalignment. It already reaches infinity somewhere between 3 meters and the actual infinity symbol. Does anyone know how to adapt the lens to correct this issue?
Thanx in advance
Peter |
|
| Back to top |
|
 |
eddieitman
 Joined: 12 Apr 2011 Posts: 1246 Location: United Kingdom
|
 Posted: Thu Mar 08, 2012 9:35 pm Post subject: |
|
 Posted: Thu Mar 08, 2012 9:35 pm Post subject: |
|
|
eddieitman wrote:
Take a look here its for the 8mm but should be the same
http://www.versacorp.com/vlink/jcreview/sy8rv9jc.pdf
section 3.4 _________________ My web site www.digital-darkroom.weebly.com
Life is like a camera. Focus on what's important, capture the good times, develop from the negatives and if things don't work out, just take another shot. |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Thu Mar 08, 2012 9:46 pm Post subject: |
|
 Posted: Thu Mar 08, 2012 9:46 pm Post subject: |
|
|
pholler wrote:
Thanx for the link. I think it's the same for the Samyang 14 but not for the 35. |
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Thu Jun 14, 2012 3:15 pm Post subject: |
|
 Posted: Thu Jun 14, 2012 3:15 pm Post subject: |
|
|
ilguercio wrote:
I have both the 35 and the 85 and they reach infinity a good couple of mm before the mark on the barrel.
What's better? Trying to fit spacers inside the mount or adjust the focus barrel? |
|
| Back to top |
|
 |
Orio
Joined: 24 Feb 2007 Posts: 29545 Location: West Emilia
Expire: 2012-12-04
|
 Posted: Thu Jun 14, 2012 3:21 pm Post subject: |
|
 Posted: Thu Jun 14, 2012 3:21 pm Post subject: |
|
|
Orio wrote:
Infinity calibration cost about 20 Euros in lens repair shops here.
I start to doubt seriously about the quality of the product though, if so many buyers report this problem.
One case may be bad luck, but so many cases means there's a poor production issue. _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Thu Jun 14, 2012 3:29 pm Post subject: |
|
 Posted: Thu Jun 14, 2012 3:29 pm Post subject: |
|
|
ilguercio wrote:
It's a korean lens, you can't expect much in this aspect.
They obviously have to cut costs and as long as the lens works, is smooth and doesn't have mayor issues i'm fine with what i payed for it.
This isn't a huge problem, doesn't make the lens unusable but it is certainly annoying.
Just remember that everytime we adapt a lens chances are we will have to change infinity due to differences in the thickness of the adapters. |
|
| Back to top |
|
 |
Orio
Joined: 24 Feb 2007 Posts: 29545 Location: West Emilia
Expire: 2012-12-04
|
 Posted: Thu Jun 14, 2012 3:33 pm Post subject: |
|
 Posted: Thu Jun 14, 2012 3:33 pm Post subject: |
|
|
Orio wrote:
| ilguercio wrote: |
It's a korean lens, you can't expect much in this aspect.
They obviously have to cut costs and as long as the lens works, is smooth and doesn't have mayor issues i'm fine with what i payed for it.
|
I agree. Even if you add the cost for infinity adjustment, it is still a great bargain compared to the prices of Nikon and Canon lenses. _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Thu Jun 14, 2012 3:39 pm Post subject: |
|
 Posted: Thu Jun 14, 2012 3:39 pm Post subject: |
|
|
ilguercio wrote:
The problem with the 85 is that under the mount is a hollow space with just the screw holes protruding and setting the distance of the bayonet to the lens barrel.
The screw holes don't have enough space to be "lifted" with spacers so i guess i have to think differently or fiddle with the focus ring if i can reach it easily.
I haven't opened the 35's mount yet, it is probably different as the differences in the construction suggest but i have to check.
I'll post some pictures later.
 |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Mon Jun 18, 2012 5:53 am Post subject: |
|
 Posted: Mon Jun 18, 2012 5:53 am Post subject: |
|
|
pholler wrote:
| Orio wrote: |
I start to doubt seriously about the quality of the product though, if so many buyers report this problem.
One case may be bad luck, but so many cases means there's a poor production issue. |
I own three Samyang lenses and none of them reached infinity when it reached me. Once i sent the 14/2.8 back to amazon just because of that and got a new one which was even worse. Then i started to accept the fact and just did the adjustment myself. I also did it on the 8/3.5 but i have no clue how to do it on the 35/1.4. _________________
EOS 5D Mark II
CZ: Makro-Planar T* ZE 50/2
CZJ: Sonnar 135/3.5 electric MC
Walimex/Samyang: 14/2.8, 35/1.4
Sigma: Makro 70/2.8, 70-200/2.8
Tamron: 24-70/2.8
|
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Mon Jun 18, 2012 10:55 am Post subject: |
|
 Posted: Mon Jun 18, 2012 10:55 am Post subject: |
|
|
ilguercio wrote:
| pholler wrote: |
| Orio wrote: |
I start to doubt seriously about the quality of the product though, if so many buyers report this problem.
One case may be bad luck, but so many cases means there's a poor production issue. |
I own three Samyang lenses and none of them reached infinity when it reached me. Once i sent the 14/2.8 back to amazon just because of that and got a new one which was even worse. Then i started to accept the fact and just did the adjustment myself. I also did it on the 8/3.5 but i have no clue how to do it on the 35/1.4. |
How you did it?
I mean, spacers or you changed the reciprocate position between the focus ring and the barrel? |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Mon Jun 18, 2012 11:16 am Post subject: |
|
 Posted: Mon Jun 18, 2012 11:16 am Post subject: |
|
|
pholler wrote:
| ilguercio wrote: |
How you did it?
I mean, spacers or you changed the reciprocate position between the focus ring and the barrel? |
First i started trying it with spacers but that's crap. Then i removed the plastic around the focusing ring. You will find screws and a tape underneath. You can find instructions how to do that when you google it. I am going to send you a link with pictures in the evening... _________________
EOS 5D Mark II
CZ: Makro-Planar T* ZE 50/2
CZJ: Sonnar 135/3.5 electric MC
Walimex/Samyang: 14/2.8, 35/1.4
Sigma: Makro 70/2.8, 70-200/2.8
Tamron: 24-70/2.8
|
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Mon Jun 18, 2012 11:34 am Post subject: |
|
 Posted: Mon Jun 18, 2012 11:34 am Post subject: |
|
|
ilguercio wrote:
Thanks, i appreciate it.
 |
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Mon Jun 18, 2012 3:35 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 3:35 pm Post subject: |
|
|
ilguercio wrote:
Isn't there the chance of the rubber becoming loose after removing it from the ring?
Haven't had any problem with the 70-200 or the 18-55 IS but i don't know about Samyang. |
|
| Back to top |
|
 |
poilu
 Joined: 26 Aug 2007 Posts: 10476 Location: Greece
Expire: 2019-08-29
|
 Posted: Mon Jun 18, 2012 4:07 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 4:07 pm Post subject: |
|
|
poilu wrote:
I fixed my 14:2.8 with this http://www.photo-worx.de/index.php?option=com_content&task=view&id=55&Itemid=
it is great, wide open I just set infinite without the need to confirm focus with liveview or viewfinder
it is important to fix infinite, especially for wide where we use mostly infinite _________________ T* |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Mon Jun 18, 2012 5:09 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 5:09 pm Post subject: |
|
|
pholler wrote:
I am glad you could adjust the infinity focus. I used the same page when i was doing it.
I recommend getting a Dandelion chip for this lens. Focusing with pure eye-sight is quite difficult at 14 mm. _________________
EOS 5D Mark II
CZ: Makro-Planar T* ZE 50/2
CZJ: Sonnar 135/3.5 electric MC
Walimex/Samyang: 14/2.8, 35/1.4
Sigma: Makro 70/2.8, 70-200/2.8
Tamron: 24-70/2.8
|
|
| Back to top |
|
 |
poilu
 Joined: 26 Aug 2007 Posts: 10476 Location: Greece
Expire: 2019-08-29
|
 Posted: Mon Jun 18, 2012 5:56 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 5:56 pm Post subject: |
|
|
poilu wrote:
| pholler wrote: |
I am glad you could adjust the infinity focus. I used the same page when i was doing it.
I recommend getting a Dandelion chip for this lens. Focusing with pure eye-sight is quite difficult at 14 mm. |
with this lens, if the infinity stop is well calibrated, you don't need to focus
at F8 the dof is from 40cm to infinity
at F2.8 from 1.2m to infinity _________________ T* |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Mon Jun 18, 2012 6:30 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 6:30 pm Post subject: |
|
|
pholler wrote:
| poilu wrote: |
with this lens, if the infinity stop is well calibrated, you don't need to focus
at F8 the dof is from 40cm to infinity
at F2.8 from 1.2m to infinity |
Yes, but this lens makes also makes fun with focus distances nearer than infinity and focusing this is quite difficult. _________________
EOS 5D Mark II
CZ: Makro-Planar T* ZE 50/2
CZJ: Sonnar 135/3.5 electric MC
Walimex/Samyang: 14/2.8, 35/1.4
Sigma: Makro 70/2.8, 70-200/2.8
Tamron: 24-70/2.8
|
|
| Back to top |
|
 |
poilu
 Joined: 26 Aug 2007 Posts: 10476 Location: Greece
Expire: 2019-08-29
|
 Posted: Mon Jun 18, 2012 6:48 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 6:48 pm Post subject: |
|
|
poilu wrote:
| pholler wrote: |
| Yes, but this lens makes also makes fun with focus distances nearer than infinity and focusing this is quite difficult |
nice, I am waiting your samples in the galleries to get some idea  _________________ T* |
|
| Back to top |
|
 |
pholler
Joined: 08 Mar 2012 Posts: 17 Location: Austria
|
 Posted: Mon Jun 18, 2012 7:18 pm Post subject: |
|
 Posted: Mon Jun 18, 2012 7:18 pm Post subject: |
|
|
pholler wrote:
| poilu wrote: |
nice, I am waiting your samples in the galleries to get some idea  |
I just checked my LR-library and i did some shots of people indoors when there is not much space, like in the kitchen using a crop-camera. Especially cutting a cake or unpacking Christmas presents. On FF it is too wide for such an application. On FF it is too wide for nearly everything. _________________
EOS 5D Mark II
CZ: Makro-Planar T* ZE 50/2
CZJ: Sonnar 135/3.5 electric MC
Walimex/Samyang: 14/2.8, 35/1.4
Sigma: Makro 70/2.8, 70-200/2.8
Tamron: 24-70/2.8
|
|
| Back to top |
|
 |
ZoneV
 Joined: 09 Nov 2009 Posts: 1633 Location: Germany
Expire: 2011-12-02
|
 Posted: Thu Jun 21, 2012 8:02 am Post subject: |
|
 Posted: Thu Jun 21, 2012 8:02 am Post subject: |
|
|
ZoneV wrote:
| Orio wrote: |
...
I start to doubt seriously about the quality of the product though, if so many buyers report this problem.
One case may be bad luck, but so many cases means there's a poor production issue. |
For me it seems that 10-30% have not a right adjusted focus scale.
I could live with that. On my Samyang 14mm lens the adjustment of the internal focus didn´t worked - it was to limited. So I made the register distance approach http://www.4photos.de/camera-diy/Samyang-Walimex-Rokinon-Vivitar-Falcon-14mm-2.8-Focus-Correction.html
This helped and worked good.
But after some time infinity was deadjusted again (no drop), and the hole front part wobbles. With three outer screws I could "fix" that. And I took the shims away - infinity ok.
But the screws seem to influence the iris, it was stuck sometimes.
Again some time later the lens front wobbels again, outer screws did not help.
Opend the lens a bit more. There where three screws deeper inside the lens barrel loose. Those screws hold front and back part together. I pressed font and back togehter to get parallelism. But afterwards I saw that the lens is tilted even with those parts pressed togehter. For me it seems (not sure) that Samyang adjust with a special machine front and back part, and then close the screws in this machine. This would result in a nearly not serviceable lens.
Furthermore I only read from people that they have their lens with problems replaced with a new one. Never read from repaired lenses apart from DIY approaches (or some tinkering workshops). _________________ Camera modification, repair and DIY - some links to look through: http://www.4photos.de/camera-diy/index-en.html
I AM A LENS NERD!
Epis, Elmaron, Emerald, Ernostar, Helioplan and Heidosmat.
Epiotar, Kameraobjektiv, Anastigmat, Epis, Meganast, Magnagon, Quinar, Culmigon, Novotrinast, Novflexar, Colorplan, Sekor, Kinon, Talon, Telemegor, Xenon, Xenar, Ultra, Ultra Star. Tessar, Janar, Visionar, Kiptar, Kipronar and Rotelar.
|
|
| Back to top |
|
 |
poilu
 Joined: 26 Aug 2007 Posts: 10476 Location: Greece
Expire: 2019-08-29
|
 Posted: Thu Jun 21, 2012 9:10 am Post subject: |
|
 Posted: Thu Jun 21, 2012 9:10 am Post subject: |
|
|
poilu wrote:
| ZoneV wrote: |
| For me it seems that 10-30% have not a right adjusted focus scale |
maybe they put the mount at the last minute, if they calibrate for Nikon then put a Canon mount that could explain this mess
anyway calibrating this lens is easy, don't use the washer method
use those instructions http://www.photo-worx.de/index.php?option=com_content&task=view&id=55&Itemid=
for those who don't understand German (like me), this is what I did on mine
- remove the rubber, it is elastic but take your time
- set lens at f2.8 and adjust infinity on borders (with liveview), you will be little more than 2m on the scale
- unscrew the 3 screw marked '1' by 2 or 3 turns
- with a screwdriver move the inside barrel '2' until the max (infinity stop) without moving the exterior so you stay at 2m on the scale
- screw back the 3 screws
- now the infinite is at max but the scale is at 2m instead of infinite, you have to remove the scotch '3', move the scale to infinite and put scotch back
- put the rubber back
I had problem to set the scale at infinite, even after removing the scotch it was like glued, but after playing up down, right left, it moved freely and I could put it to the right place
| ZoneV wrote: |
| But after some time infinity was deadjusted again (no drop), and the hole front part wobbles |
I hope mine keep in shape for longer, first time I see a lens assembled with scotch
| ZoneV wrote: |
I suppose that correction alter the IF - internal focussing
One can not know, which is "the right one" |
it just change the infinity stop not the internal focusing so it is the right method, shimming would be good if no other method existed _________________ T* |
|
| Back to top |
|
 |
ZoneV
 Joined: 09 Nov 2009 Posts: 1633 Location: Germany
Expire: 2011-12-02
|
 Posted: Mon Jul 16, 2012 8:28 am Post subject: |
|
 Posted: Mon Jul 16, 2012 8:28 am Post subject: |
|
|
ZoneV wrote:
| poilu wrote: |
...I hope mine keep in shape for longer, first time I see a lens assembled with scotch
.. |
There are a lot of lenses with taped internals. This is used because it is easier to handel than screws on such elements.
First heard about this ~15 years ago, when my brothers Sigma zoom fell apart in hot enviroment and sun.
On newer lenses this is quite often used. But even on the Minolta Rokkor 28mm/2.0 the infinity stop and focus scale is hold with tape (when I remember correct).
| poilu wrote: |
...
| ZoneV wrote: |
I suppose that correction alter the IF - internal focussing
One can not know, which is "the right one" |
it just change the infinity stop not the internal focusing so it is the right method, shimming would be good if no other method existed |
I tested first the other method with correction of IF or infinity stop - but it did not work for my lens.
Afterwards I made the register distance correction. Waht worked well for a while.
But I realized that internal screws are loose. It seems the hole lens parallelity depends on three or four screws. When they open, it is very hard to adjust the lens without Samyang tools. Have to do this now. _________________ Camera modification, repair and DIY - some links to look through: http://www.4photos.de/camera-diy/index-en.html
I AM A LENS NERD!
Epis, Elmaron, Emerald, Ernostar, Helioplan and Heidosmat.
Epiotar, Kameraobjektiv, Anastigmat, Epis, Meganast, Magnagon, Quinar, Culmigon, Novotrinast, Novflexar, Colorplan, Sekor, Kinon, Talon, Telemegor, Xenon, Xenar, Ultra, Ultra Star. Tessar, Janar, Visionar, Kiptar, Kipronar and Rotelar.
|
|
| Back to top |
|
 |
ilguercio
 Joined: 08 Mar 2012 Posts: 414 Location: Southern Italy-Calabria!
|
 Posted: Fri Sep 28, 2012 3:51 pm Post subject: |
|
 Posted: Fri Sep 28, 2012 3:51 pm Post subject: |
|
|
ilguercio wrote:
There is in fact a set of screws under the focus rubber ring but in the case of the 35 the ring is coupled to the helicoid in one defined position. I tried to unscrew the lower ones and then adjust the ring to the new infinity but the helicoid itself has already defined holes for the screws to fit into so there's no way to adjust the reciprocate position between the ring and the helicoid.
I ended up fitting spacers between the lens barrel and the mount.
For the 85 a single layer of electricaltape gave me a pretty much correct infinity (i'm lucky), but for the 35 i have to find something a bit thinner.
Just keep in mind that the spacer has to lay on the outer rim of the mount, otherwise you can't change the aperture because it blocks it ring. |
|
| Back to top |
|
 |
|
|