MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

Rubber focus ring loose, how to fix?
View previous topic :: View next topic  


Reply

Anybody got any tips for re gluing a rubber ring. What type of glue to use etc.
I was thinking of just using super glue but I don't think that's a good idea. Since it can melt plastic, I'm not sure if it would do the same thing with rubber, but I don't care much to find out if it does. And it's probably not to good for glass either.

If it makes any difference it's for an Olympus 50mm f1.4


Reply

Do you need to be able to remove the ring at a later date ? Some rubber rings hide screws of various types.

If you might wish to remove it you might try a latex based adhesive. I don't think that this would form a permanent bond to metal - but I might be wrong and you should do your own research.

If you are not worried about removing it there is a general purpose adhesive called "UHU". I've used it for gluing the fabric collar which provides the friction for built in lens hoods such as those on the CZJ 3.5/135. But I haven't tried it on a rubber ring.


Reply

Yea there is some screws underneath it. I will look into latex based adhesive. Amongst other non "permanent" solutions.
Thank you sichko.


Reply

Hi,
I would also go with non permanent solution. In the past I used few drops of clear silicone (the type used for plumbing). It worked well for me with no collateral effects.
Marty.


Reply

The regular camera repair glue for all kinds of covers would be Pliobond.

Sevo


Reply

Found another way to fix it, I very slowly heated the rubber with a small butane heater that I use for shrinking shrink wraps on electric wires.
Leaving the lens in the sun would probably have done the same thing and be safer. Razz

That seems to have reactivated part of the glue and shrunk the rubber enough that it isn't loose anymore and there's no damage to the rubber.
This might just be temporary, so I guess I'll have to wait and see how it holds up.
If that doesn't hold up, I'll go get some silicone. Smile


Reply

My 35-80 Tamron is a well-used one and the rubber zoom ring is as loose as a cow's backside. I put a layer of double-sided sticky tape under it and it's been ok for a year now.


Reply

My copy of a Hanimar 70-140 also has a loose rubber grip,
but it's also expanded, now longer than the barrel position
it was sized for. It's tight enough, but it sticks over the flange
of the aluminum barrel at one end.

I have been wondering how to best trim the extra length of no more
than 1.5mm in a straight line, and nothing acceptable comes to mind.
Any suggestions?


Reply

Hi,
I had the same problem with a Tamron 40A. I glued the rubber with few tiny drops of clear silicone having great care in positioning one side of it against one border of the sunken seat in the barrel and let it cure. I then carefully trimmed the excess with a sharp cutter using the other border of the sunken seat as a guide while holding the barrel on the workbench with the palm of my hand and pressing the rubber with a finger tip against said border.
The cut is neat enough, to my standards at least, even if not quite perfect. In other words a very close inspection will tell something has been done, at first sight is almost not noticeable.
Whether the manufacture of your lens is similar to mine and thus if my method does apply is to see.
http://www.flickr.com/photos/50931367@N00/3494429947/
BE VERY CAREFUL with the cutter: if not enough attention is paid serious injure can occure. An unsharp blade will lead to less then perfect job.
Marty.