MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

This pentax adapter has bugged me for awhile...
View previous topic :: View next topic  


Reply

I bought this as a genuine Pentax adapter but it does not lock in the camera mount...it is identical to my other adapter except for the raised screw head is slightly rounded not flat as in the other adapter that locks happily into the camera mount....can some of you guys check what sort of screws are in your original adapters to see if that may be the reason why it will not lock......Thanks
#1

#2

#3

#4

#5

#6

#7

#8

#9


Reply

What do you mean with "it will not lock"? If it can be turned in the bayonet then I'd suggest to bend that little piece of black sheetmetal a little more to the outside of the adapter, because THAT is the lock. Hard to explain for me, as I'm not a native English speaker Smile


Reply

Thank you....when I use the other adapter it will stay in the mount while I can unscrew the lens from it,where as this adapter in the photos will unscrew off with the lens.I tried bending it early on but did not know which direction to bend the black metal.

That fixed it...something so small as bending it the right way... Very Happy Very Happy


Last edited by mo on Mon Jan 24, 2011 8:00 am; edited 2 times in total


Reply

Well, when looking at photo #8: just push the black metal up and see if that helps!


Reply

If you've not allready solved this...

It sounds to me as if the screw might be fouling on part of the mount. Try swapping the screws between your two mounts, keeping the springs as they are, if the problem moves to the other mount find a screw with a lower head.

Alternatively do as I do & remove the screw & spring. Mount the adapter permanantly on your favorite M42 lens (a drop of thread lock may be worth using) & drill a slight indent in the right place for the cameras locking pin. This changes the M42 lens to a PK one, that locks in the same way as all the other bayonet lenses.


Reply

DConvert wrote:
If you've not allready solved this...

It sounds to me as if the screw might be fouling on part of the mount. Try swapping the screws between your two mounts, keeping the springs as they are, if the problem moves to the other mount find a screw with a lower head.

Alternatively do as I do & remove the screw & spring. Mount the adapter permanantly on your favorite M42 lens (a drop of thread lock may be worth using) & drill a slight indent in the right place for the cameras locking pin. This changes the M42 lens to a PK one, that locks in the same way as all the other bayonet lenses.


That's exactly what I do, no more problems. I have a bit of old camera body with the lens mount on that I use as a jig to drill the small hole for the locking pin in the lens. That's a great help.


Reply


Obviously when I'm actually drilling I get my wife to hold the lens steady and the back of the lens is covered in tissue to stop the swarf getting inside. I use a hand drill to get full control of the depth, all I need is 1.5 mm - and by using a hand drill I can, with care, drill a hole right on the edge of a lens. The Pentacon 30 has a half hole but it's enough for the pin to lock the lens in place




It's a sad end for a ME Super, but better that it still has some use than none at all. I just took the front mount ring off, removed the lock pin and spring, and that's my jig. I use a 2 or 2.5mm diameter drill.


Reply

Moira, the screw on my adapter is a flat-head type, it sits proud of the spring but has a flat surface. If you can get the adapter in flush with the mount then the screwhead is not causing any problems - it would only be a problem if it was too big to fit inside the minimum diamter of the bayonet lugs.

If you look in the lens opening of your camera there is a little metal tab inside the mount, behind the bayonet lugs, right next to the red dot, That's what the adapter locks onto, so you should bend the lock outwards so that it catches on this tab.


Reply

If I put an adapter with a spring into my jig ( the camera mount ) I can see from the inside that the screw would have to be a bit bigger to foul on anything.


Reply

Spotmatic's answer did the trick for me,but gee you guys are good at coming up with fixes! Cool