MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

Pentax ME super problem
View previous topic :: View next topic  


Reply

I picked up a bunch of camera bodies from gumtree. I was mostly interested in an old Edixa Reflex. However a couple of ME supers were in the box. One's mirror was jammed up and the other doesn't appear to meter with new batteries in it. Both otherwise look in nice clean condition.

Is there a simple cure for these woes??


Reply

Jammed mirror may be due to gummed up mechanism under the baseplate. Similar case to Spotmatic actually.
The ME Super should fire at flash sync speed with no batteries so its relatively easy to diagnose mechanical problems.
Be careful about electronics/connectors under the base.
Various other things could be wrong.


Reply

Most seem to jam sometime, and the fix isn't that hard - there's some good instructions on the internet - I know I have them bookmarked so I'll post them shortly.
The mirror is possibly stuck to the foam rubber bumper at the top of the lens housing, there are also some rubber bumpers on the mirror mechanism inside the camera, but I've always been lucky and they haven't been the cause of a stuck mirror.

http://www.pentaxforums.com/forums/120-general-technical-troubleshooting/196976-spotmatic-mirror-return.html

The light seals will almost certainly be a sticky mess and need replacing, if they are bad then the mirror bumper will be the same. Gently push the mirror away from the bumper and it should flick down, don't force it all the down.


Reply

The mirror was stuck to the bumper and came down. I read somewhere that if you wind on then let the winder lever come only so far back then push it again you can feel the mechanism engage and it fires next time. That it does but I'll take a look underneath and follow the directions given in Dave's link.

The other with no shutter/mirror problems appears to have no electronics. Any ideas?


Reply

Have a look on here under the ME repair,Attila has made them a download...and I can't actually remember what was in them.
http://forum.mflenses.com/pdf-links-1981-repairers-journals-t61261.html


Reply

Thanks Mo, but all the links download the same document. Interesting stuff though.


Reply

http://www.kyphoto.com/classics/pentaxmeproblems.html

Go straight to option2 and take the bottom plate off. What I do is prod the silver, lower, lever a bit in every direction it releases the jam. If it's option 1 and the little tab is broken off then it's a pile of spare parts.

Works for me every time, I've done 5 or 6 now.


Reply

Bugger bugger bugger. I followed the option B and pressed the lever down. It seems to catch now. Attempting to take off the top plate (unsuccessfully) I managed to push the rewind shank into the camera body. Now I cant open it and fix the crank back. Bugger!!


Reply

Had a similar problem with a spotmatic.
If its a hollow shaft you may be able to fish or out with a wire.


Reply

Get a bit of Wire coathanger about 150mm long, bend about 4mm over on the end and hit it down to a very tight U bend with a hammer. Use a fine file to round it off so it fits down the hole. Make sure the end of the bent over bit is hooked slightly. Then poke it down the hole, fiddle about until it hooks under the catch / end of the tube and lift. The film door opens. Wink


Reply

Spent an hour fiddling about. Bugger it its going back in the box. The other fires ok but no electronics. Any ideas? Help!


Reply

I can't find my bit of wire, if I find it I'll send it to you - or I'll make another. I opened a Spottie that I broke the rewind crank off just about instantly with the bit of bent wire. I've got a dead one, I'll mess with it over the weekend.


Reply

Pencil eraser the battery compartment contacts; bent contacts relax over time, need to be un-bent a little for more pressure on battery.


Reply

Dont worry Dave, everything is ok now. I dont know why I didnt take it out before closing the camera!!

I'll clean the contacts and bend them out a bit as visualopsins suggests.

Thanks for your help.