MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

New to Film Processing. Mainly happy, but......
View previous topic :: View next topic  


Reply

I finally bit the bullet and bought a home developing kit that came with Ilford Simplicity. I was pleased with my first results and so I bought Ilfosol 3 and used it for the next few films, again I was pleased with the results, though grain was quite apparent in all the films. I have now decided to try Ilfotec LC29 for my next batch of films.

Is Ilfosol inherently grainy? Or is it because of my temperatures may have been up to 1C over? I use tap water for mixing, but use filtered water for final wash - could this be an issue?

An example of Tri-X at box speed develped in Ilfosol 3:


#1


Reply

How much did you agitate the tank?


Reply

kansalliskala wrote:
How much did you agitate the tank?


First 30 secs and then 10 secs every minute. I use a stop bath rather than water at the end of development too.


Reply

I guess you could call me Old School when it comes to B&W development. For about 40 years I have used either Tri-X or Plus-X Pan (which is no longer available) with Kodak D-76 developer. I was almost a complete noob when I shot my first roll of B&W, but from the beginning and ever since, I have developed all my B&W film -- I've never sent it out.

Assuming your above photo was shot with 35mm film, it looks a lot like the results I get with Tri-X and D-76. I don't use a stop bath, just water. I also agitate differently. I invert my developing tank. I hold it at arm's length then turn it 90 degrees to the left, back to center, then 90 degrees to the right, then back to center. I do this three times every 30 seconds. This process takes about 5-6 seconds for all three rotations.

B&W is pretty forgiving stuff. I think you'd have to deviate by a considerable amount to see a noticeable change in results.


Reply

cooltouch wrote:
......Assuming your above photo was shot with 35mm film, it looks a lot like the results I get with Tri-X and D-76. .....


My next film to try is Delta 400 (I was feeling rich) so I will see how that works out.

I don't remember graininess in the shots I took way back, but in those days we only viewed them as 6"x4" prints, not big on large monitors! Laughing


Reply

About 20 film develops later: I think LC29 is slightly better for grain, but also I think Tri-X is quite a grainy film, though it did handle that sky quite well without filters.


Reply

1 degree wont make much different, technically a few seconds off the time but a film is still developing while you're pouring the dev out of the tank and just before you stop it so timing isn't exact. (others may disagree but in 50 my year experience i've never noticed.

tap water for mixing wont affect normal developers as the concentration of dissolved solids are extremely small.

Filtered water wont make any difference to grain or washing. My suggested method is used cold tap water to wash the film then thoroughly rinse it in de-ionised water (from car spares department) this stops drying spots (which you would get from normal the dissolved solids in unfiltered tap water.)

If you scan these at home, the scan setting of 'unsharp mask' should OFF if there is one. Having it ON increases the apparent grain.

Films are made differently and developers have specific properties. Any combination will give a useable negative but find the correct developer for the type of film that you're using. Researching the film type will help. Your choice of ilfosol is designed for fine grain slow and medium films. You used tri-x which is 400iso - fast and grainy.


Reply

Through recent experience I have learned to scan my negatives with everything switched off in Silverfast, so no sharpening, no film presets and no exposure adjustments as adjustments in Lightroom don't seem so harsh. Unfortunately, I had a film preset selected for the above photo and I have re-scanned with everything off some of my first films and found that they are better edited in Lightroom.


Reply

philslizzy wrote:


...then thoroughly rinse it in de-ionised water (from car spares department) this stops drying spots (which you would get from normal the dissolved solids in unfiltered tap water.)



Interesting. Do you still need to wipe the film afterwards, or can you just hang it to let it dry and get good results?


Reply

Your results look like any TriX picture, tonality is great and the grain looks like TriX
Your development seems fine but it seems to me what bothers you is grain.
Grain is a part of life, especially with TriX, Ilfosol or LC29 wont change that much, maybe Microphen or FX-39 might reduce it a little but then you lose the TriX look.

If you want grainless try Ilford Delta 100 or Tmax100. Delta 400 is very good and grain is much smaller but it is there.


skida wrote:

First 30 secs and then 10 secs every minute. I use a stop bath rather than water at the end of development too.


Reply

I found that the best adjustment was to my expectations! I have also purchased a digital thermometer as the mercury one had been dropped and I noticed some gaps in the mercury making the readings suspect. I recently went out on a very dull day and ended up pushing HP5+ to 1600 iso and developing in LC29 for 14 mins. I am very pleased with the results:

#1


Reply

skida wrote:
I have also purchased a digital thermometer as the mercury one had been dropped and I noticed some gaps in the mercury making the readings suspect.


Not just suspect, gaps in the thread make mercury in glass thermometers read wrong.

The mercury can usually be rejoined, by cooling the bulb then hold the column bulb outer most give the thermometer a rapid swing & stop suddenly (being very careful not to hit anything or otherwise break the thermometer). I've seen this successfully done dozens of times at work where we used to use hundreds of precision mercury in glass thermometers.
Only done it a couple of times myself, but I tend to work in a separate part of the lab.

Love that last shot BTW. Like Dog


Reply

NICE!
you should consider Microphen next. It is a real step up form LC29
You can buy the 1L powder, mix it, and store in small brown bottles filled to the brim. Use one bottle at a time.
That way it keeps longer.

skida wrote:



Reply

ZuikosHexanonsandVivitars wrote:
philslizzy wrote:


...then thoroughly rinse it in de-ionised water (from car spares department) this stops drying spots (which you would get from normal the dissolved solids in unfiltered tap water.)



Interesting. Do you still need to wipe the film afterwards, or can you just hang it to let it dry and get good results?


no need to wipe, thats just inviting scratches.


Reply

philslizzy wrote:
no need to wipe, thats just inviting scratches.


Thank you Like 1