| View previous topic :: View next topic |
| Author |
Message |
Väsen
Joined: 06 Sep 2011 Posts: 38
|
 Posted: Thu Oct 18, 2012 8:08 pm Post subject: CJZ 135 f/3,5 re-assembly- aperture rod and its holder issue |
|
 Posted: Thu Oct 18, 2012 8:08 pm Post subject: CJZ 135 f/3,5 re-assembly- aperture rod and its holder issue |
|
|
Väsen wrote:
Hi.
I've taken the 135 MC apart once before and reassembled it without any real issues, via http://www.andrew.brown.dsl.pipex.com/articles/czj135svc/ . I never understood what he means by "With the focussing ring set on infinity you need to turn the focussing barrel(3) all the way inwards (infinity is when the lens is at its shortest) so that it comes right off its thread." since there's a break in the thread(360 degrees) near its end so if you try to screw it 'right off its thread' it instead gets severely stuck; but by something like blind luck it got screwed in so that infinity was lined up with the infinity mark last time.
The primary issue this second time around (and don't use Tri-Flow grease for focusing helicoids) is that I can't get 'holder' in the top part, for the aperture rod, to align with the rod. The lever for A and M modes always works when I put the top on, but the little rod simply will not stay in the holder. Nothing looks bent. I'm seriously considering leaving it in A mode and truncating the peg so that the lens stays wide open, since I almost always use it like that. It just seems like a shame because the rod should stay in the holder when I snap the top part on.
Has anyone any hint? |
|
| Back to top |
|
 |
Väsen
Joined: 06 Sep 2011 Posts: 38
|
 Posted: Sat Oct 20, 2012 11:31 am Post subject: |
|
 Posted: Sat Oct 20, 2012 11:31 am Post subject: |
|
|
Väsen wrote:
I suppose not. Oh well, since this lens was always used wide open when it was used, I removed the mode selector lever of the top part, inlcuding the mode pin that sticks out(I unscrewed it, the operation can theoretically be reversed).
With nothing to manipulate the mode selector lever of the body, the aperture defaults to wide open and the two switches on the top do nothing.
Shall receive a Super Tak 135 f/3,5 early next week and it'll be interesting to see the differences (at f/3.5). People say the Super Tak can have nervous bokeh, but so can this aus Jena, the thing I love it for is its sharpness wide open. |
|
| Back to top |
|
 |
fermy
 Joined: 17 Feb 2012 Posts: 1974
|
 Posted: Sun Oct 21, 2012 2:33 am Post subject: |
|
 Posted: Sun Oct 21, 2012 2:33 am Post subject: |
|
|
fermy wrote:
I've never disassembled this particular lens, however, I've disassembled other CZJ lenses. IMHO the instructions at this point are simply wrong. It's very difficult (but sometimes you get lucky) to mate helicoids from the rear, where the threads end rather than start. This is the problem you are having.
There should be a way to unscrew the focusing barrel from the front of the lens and consequently screw it back in from the front. That way the threads should mate easily and after some trial and error you will find the correct starting position and line up everything correctly. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| Back to top |
|
 |
Väsen
Joined: 06 Sep 2011 Posts: 38
|
 Posted: Mon Oct 22, 2012 12:32 pm Post subject: |
|
 Posted: Mon Oct 22, 2012 12:32 pm Post subject: |
|
|
Väsen wrote:
Hi.
Indeed, there is a way to mate the barrel with the helicoid from the top and get proper focus. In some old post someone suggested there was were marks on the helicoid and the barrel to indicate where the threads should meet, however I failed to find any such mark. There is a distinct 'V' on the focus ring however, but as there's nothing on the helicoid it doesn't help much.
The issue I was having here was with the aperture rod and the top piece however : ) |
|
| Back to top |
|
 |
fermy
 Joined: 17 Feb 2012 Posts: 1974
|
 Posted: Wed Oct 24, 2012 4:37 am Post subject: |
|
 Posted: Wed Oct 24, 2012 4:37 am Post subject: |
|
|
fermy wrote:
What I am saying is that you should try mating the helicoid from the top until the top piece and rod line up properly.
The reason why I suggest doing it from the top is that it's 10x faster than from the bottom, so trial and error approach is feasible. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| Back to top |
|
 |
Väsen
Joined: 06 Sep 2011 Posts: 38
|
 Posted: Wed Oct 24, 2012 4:01 pm Post subject: |
|
 Posted: Wed Oct 24, 2012 4:01 pm Post subject: |
|
|
Väsen wrote:
I'm afraid I don't understand. The main body (helicoid) mates with the focussing barrel. You can do that from the top or try to do it from the bottom.
The top part however, this : http://www.andrew.brown.dsl.pipex.com/articles/czj135svc/images/2.jpg is simply snapped onto the helicoid , preferrably with the aperture rod 'fastened' to its holder and the mode lever selection rod over the mode lever. There is no 'top' or 'bottom' part of this that I can conceive of. |
|
| Back to top |
|
 |
fermy
 Joined: 17 Feb 2012 Posts: 1974
|
 Posted: Wed Oct 24, 2012 5:15 pm Post subject: |
|
 Posted: Wed Oct 24, 2012 5:15 pm Post subject: |
|
|
fermy wrote:
The part you are showing is screwed onto the rest of the lens. So if something does not line up properly, chances are that the rest of the lens has been assembled incorrectly. _________________ Many lenses and some film bodies for sale here: http://forum.mflenses.com/canon-fd-minolta-md-c-mounts-m42-pentax-and-more-t50465.html
Flickr http://www.flickr.com/photos/96060788@N06/ |
|
| Back to top |
|
 |
Väsen
Joined: 06 Sep 2011 Posts: 38
|
 Posted: Thu Oct 25, 2012 9:12 am Post subject: |
|
 Posted: Thu Oct 25, 2012 9:12 am Post subject: |
|
|
Väsen wrote:
No, it doesn't screw on, it's just put on. It isn't a question of anything to do with the helicoid threads or anything else, it's merely a question of being deft-of-hand enough to get the holder in the top part to 'mate' with the aperture lever properly. |
|
| Back to top |
|
 |
Gonzoo
 Joined: 29 Mar 2010 Posts: 231
|
 Posted: Tue Nov 06, 2012 10:16 am Post subject: |
|
 Posted: Tue Nov 06, 2012 10:16 am Post subject: |
|
|
Gonzoo wrote:
Don't know if this helps, but I fixed a CZJ MC 135mm a few weeks ago using these instructions:
https://picasaweb.google.com/111466649819981314803/CZJ135Repair
https://secure.flickr.com/photos/34694152@N00/746619911/in/set-72157594512669706/
offtopic: Fermy, can you provide me with some images of the two springs near the apperture? _________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| Back to top |
|
 |
philslizzy
 Joined: 07 Aug 2012 Posts: 4753 Location: Cheshire, England
|
 Posted: Fri Nov 23, 2012 11:50 pm Post subject: |
|
 Posted: Fri Nov 23, 2012 11:50 pm Post subject: |
|
|
philslizzy wrote:
| Väsen wrote: |
| No, it doesn't screw on, it's just put on. It isn't a question of anything to do with the helicoid threads or anything else, it's merely a question of being deft-of-hand enough to get the holder in the top part to 'mate' with the aperture lever properly. |
On the part that comes off when you've got the three screws off is the long flat strip that controls the aperture linkage. I suggest you put the aperture on the lens in the f22 position and move the long flat strip also to the f22 position. The long strip slides into a channel on the aperture linkage on the lens side, slip that in the end first, about a couple of millimetres will do, then concentrate on the linkage on the other side, I assume you know how they mate together, jiggle them about lining up the v's, theyre both roughly v shape, they will just pop into place. I takes me a minute or so of jiggling as they've got to be exactly lined up.
I cleaned the fungus off my lens but the aperture is well sticky. I've tried lighter fluid and alcohol to no avail. I'm not taking the whole thing apart! |
|
| Back to top |
|
 |
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|