| View previous topic :: View next topic |
| Author |
Message |
guardian
 Joined: 18 Mar 2009 Posts: 1750
|
 Posted: Wed Oct 03, 2012 12:28 pm Post subject: Need suggestions restoring aluminum matte finish |
|
 Posted: Wed Oct 03, 2012 12:28 pm Post subject: Need suggestions restoring aluminum matte finish |
|
|
guardian wrote:
Does anyone know how to restore matte aluminum finish? I hope that's the right name for this. The lens has a ring of aluminum which has a uniform matte finish. There is a scratch, not too deep, which comes up shiny. I want to minimize the appearance impact of the scratch, if possible. Even just a way to subdue the shininess would help. I'm not expecting perfection.
But I'm afraid any scratch repair I try will further shine the region of the scratch, whereas I want to duplicate the surrounding matte appearance instead.
I don't know how a matte finish is achieved on aluminum. Is this done by application of a chemical? I don't know.
Any suggestions would be appreciated.
I realize this is only a cosmetic problem which does not impact function of the lens. But I still would like to improve things if I can.
Last edited by guardian on Wed Oct 03, 2012 2:17 pm; edited 1 time in total |
|
| Back to top |
|
 |
twinquartz
 Joined: 11 Jun 2012 Posts: 316 Location: Sweden
Expire: 2013-10-29
|
 Posted: Wed Oct 03, 2012 1:59 pm Post subject: |
|
 Posted: Wed Oct 03, 2012 1:59 pm Post subject: |
|
|
twinquartz wrote:
Hi guardian!
A brushed surface was (at least in the good old days) made with a brush.
In the watch collecting world, a small glassfibre tipped tool is used to
remove small, shiny areas. It is important to try to follow the original
direction of the brush strokes, otherwise you will get a patch which
does not look like the surroundings.
Google for "brushed metal" plus the word repair or tool.
Good luck! |
|
| Back to top |
|
 |
guardian
 Joined: 18 Mar 2009 Posts: 1750
|
 Posted: Wed Oct 03, 2012 2:14 pm Post subject: |
|
 Posted: Wed Oct 03, 2012 2:14 pm Post subject: |
|
|
guardian wrote:
| twinquartz wrote: |
Hi guardian!
A brushed surface was (at least in the good old days) made with a brush.
In the watch collecting world, a small glassfibre tipped tool is used to
remove small, shiny areas. It is important to try to follow the original
direction of the brush strokes, otherwise you will get a patch which
does not look like the surroundings.
Google for "brushed metal" plus the word repair or tool.
Good luck! |
I appreciate the very kind response. Thank you.
You have caused me to take a second look at this. I find I made a mistake and I apologize.
The surface I am confronting is not a "brushed" surface. But it is a matte surface. I was wrong to use the term "brushed". There are no brush marks at all. But instead the surface, setting aside the scratch, is perfectly uniform while not being shiny. How Konica created this matte surface, again, I do not know. It could be a kind of anodizing or it might have been done chemically. But it does not appear to have been created mechanically.
I have gone back and edited the OP in hope of correcting my error. Again, this was carelessness on my part. I'm sorry I used the term "brushed". |
|
| Back to top |
|
 |
twinquartz
 Joined: 11 Jun 2012 Posts: 316 Location: Sweden
Expire: 2013-10-29
|
 Posted: Wed Oct 03, 2012 2:38 pm Post subject: |
|
 Posted: Wed Oct 03, 2012 2:38 pm Post subject: |
|
|
twinquartz wrote:
Don't be sorry
In principle, a matte surface if nothing but a non-shiny, non-even surface,
which means that it is reflecting less light. The coarser and the more irregular a
surface is, the less light it will reflect - and it will look matte.
To polish something, you have to make the surface as even as possible.
To make something matte, you do the opposite, i.e. you introduce some
irregularities. Careful stippling with a glassfibre pen is one method
(if your strokes are long and regular, you will get a brushed surface).
If I were you, I would practise on some other metal object at first,
to get the feel for how to handle "the real thing". If you do not have a
glassfibre pen available, try a not-too-coarse piece of sandpaper.
Which grade to pick depends on which impression you want.
Good luck! |
|
| Back to top |
|
 |
Jethro Tull
 Joined: 31 Dec 2010 Posts: 68 Location: SCOTLAND
|
 Posted: Mon Oct 22, 2012 3:29 pm Post subject: alloy rubber |
|
 Posted: Mon Oct 22, 2012 3:29 pm Post subject: alloy rubber |
|
|
Jethro Tull wrote:
In the 1980's you used to be able to buy a small rubber block which had very fine abrasive mixed into the rubber, it was used to clean alloy motorcycle parts on my BMW's and you could get them in various grades from VERY fine to course. I cannot remember the products actual name but a fine grade one would probably work for you.
Try searching Ebay in automotive cleaners etc |
|
| Back to top |
|
 |
Jethro Tull
 Joined: 31 Dec 2010 Posts: 68 Location: SCOTLAND
|
 Posted: Mon Oct 22, 2012 3:42 pm Post subject: just found this |
|
 Posted: Mon Oct 22, 2012 3:42 pm Post subject: just found this |
|
|
Jethro Tull wrote:
Hi,
Here's something similar to the rubber block i mentioned.
http://uk.rs-online.com/web/p/abrasive-blocks-sponges/0692801/ |
|
| Back to top |
|
 |
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|