MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

#000 screwdriver recomendation needed
View previous topic :: View next topic  


Reply

I need a high quality #000 screwdriver to take apart rest of my Nikkor 20mm f4 lens. I'm trying to remove the focus slop. I believe this is the right size, it seems to fit perfectly, but mine is out of a cheap set and won't turn it.
I don't want to take the chance of stripping the head of the screw.

My other thread.

http://forum.mflenses.com/nikon-nikkor-20mm-f4-focus-slop-repair-t51841.html


Reply

Walter, try searching for watchmakers' tools or horological tools.
There are plenty suppliers in USA - I found this one (scroll to the bottom)
http://www.ofrei.com/page755.html


Reply

Thanks, Peter. Smile
The screws seem really tight, I'm not sure I could turn them with that slim of a driver.

I was thinking about either Wera or Wiha. Wera, I couldn't figure out ther code system.
Wiha, the prices seem to be alot lower then they used to be. I figured there quality might of dropped.
I saw this set on Amazon. I just don't know if the drivers are good enough.
Anyone use them lately?
http://www.amazon.com/Wiha-26199-Slotted-Phillips-Screwdriver/dp/B000NZ5QG0


Reply

Those watchmaker's screwdrivers are in my experience useless for our purposes. I have a set of screwdrivers from these pepole: http://www.proskit.com/ in all sizes and they're very good (and inexpensive). The important thing is that the screwdriver head has to be very hard, the handle must be large enough so you get enough torque and you must always use the exact right size of screwdriver for the screw! Also it's possible the screw isn't just screwed in. Often they use some sort of adhesive over the screw so it doesn't get loose by itself and that makes it hard to remove. If the screw looks like "painted over" with something, try using a drop of nail polish remover (ask your wife) before unscrewing.


Reply

miran wrote:
Those watchmaker's screwdrivers are in my experience useless for our purposes.

I think that's a very limited opinion, how much experience do you have? My father-in-law was a professional watchmaker and his tools have been extremely useful to me. Of course, as usual, if you pay little you get rubbish.


Reply

peterqd wrote:
Of course, as usual, if you pay little you get rubbish.

That's certainly true and I suppose my experience is limited to the cheap rubbish. Razz But still, "use the right tool for the job" has never been bad advice. The main problem with watchmaker's screwdrivers is that if you have a screw that is very tightly screwed in, you don't get enough torque with that small grip. It just wasn't designed for this. Watchmaker's tools are for the most part designed to be used with smaller parts. I do agree they can be useful in many cases though.


Reply

http://www.micro-tools.com/store/searchbycategory.aspx?openid=12

Jammed screw sometimes loosen:

use solder iron tip to heat (only) screw -- screw expands in hole, then contracts, to free jam.

insert precision screwdriver, strike end of screwdriver with small hammer -- sometimes frees jam.

a tiny drop of penetrating oil, not wd40 (wd = water dispersion) but "Liquid Wrench", "Marvel Mystery Oil", or neat wintergreen oil from pharmacy -- useful if jam is corrosion or something else; not much use for mechanical jam.


Reply

Great tips Visual. Another one, especially if the screw slot is worn, is to tighten it a tiny amount before trying to unscrew it. This breaks the bond and unscrewing is a lot easier.


Reply

I agree with visualopsins, a soldering iron with a point is a great help at freeing up stuck screws. Then a gentle tap on the screwdriver to seat the driver into the screw, and it jars the screw loose(er)
Witta are excellent quality screwdrivers, I've had some big ones for over 20 years and they have seen a lot of hard work and abuse as a maintenance engineer. Cheap screwdrivers are the work of the devil! Wink


Reply

Thanks, guys. Smile Hopefully I will be able to get a set of screwdrivers on order soon, and thanks for all the sugestions.
I've moved to a smaller house, and the sad thing is I have a really nice set packed away somwhere in my shed.
There is just no room to unpack rest of my stuff.