MFlenses - A new life in a digital age
MFLenses 2026

Manual Focus Lenses Forum

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.

Explore the world of vintage lenses through repair notes, real test shots, and detailed archive threads packed with images.
Spotlight

Featured partner placement for the forum front page.

Canon EOS 450D replacement focus screen issues
View previous topic :: View next topic  


Reply

I bought a replacement split-screen for my 450D as the original screen is useless for focusing manually.

I've installed it correctly, it's definitely seated properly and the right way up (will only go in one way) but it appears to not work properly.

When the two halves of the image in the central split screen are properly aligned, the image is way out of focus.

Anyone else had this issue with replacement screens?


Reply

I did for my 550D, dual 45 degree ones I ordered of ebay. Both went in the trash unfortunately, can't recall the name.
I did have a travor 180 degree single split prism first, it was spot on, but the 180 line was mostly in the way I found, so I switched back to the original.


Reply

I think I'll just sell my EOS, not been impressed with it at all, IQ is crap compared o me NEX-3 and NX100. I knew an older sensor wouldn't be as good but it's a long way behind in dynamic range, fine detail and noise.

The Canon lenses for it I've tried have not been good either, wasted a fair bit of money on those.

Not being able to use manual lenses with it is the final nail in the coffin. Sad


Reply

I am quite happy with my 550D, tho the 450D is quite a bit older.
I use alot of MF lenses on my EOS, only thing I can't use are pretty much rangefinder lenses and konica, tho the glass adapter for MD is not really good. Otherwise I have adapters for pretty much every mount.


Reply

Howdy, there.
A tiny difference in thickness compared with original and won't focus as the the focus plane is shifted. In some cases shimming can do the trick. I can't be more specific, but it's a well known issue and has been discussed. I don't know specifically this camera and lenses so cannot comment on their performance.

Cheers, M.


Reply

Ian, the thickness of the replacement screens is a little less than the OEM Canon ones I think, so they need to be adjusted. It can take several goes and needs a bit of patience. You have to experiment to get it right.

As you look through the mount, there should be a thin brass shim between the screen and the frame. This adjusts the distance between the mirror and the screen and if it isn't spot on, when the focus in the viewfinder is correct it will be wrong on the sensor. I can't remember which way round, but I think not enough shim thickness causes front focussing and too much shim thickness causes back focussing. You can check this by taking a picture looking along a tape measure. If you focus on a definite point on the measure, you can see in the resulting picture whether your camera is front or back focussing.

I had to increase the thickness of the shim in my camera. You can buy a set of shims of different thicknesses from Canon (they call them "washers"), but I just used two tiny pieces of 3M Magictape, one on each side of the shim.

There are several threads discussing this. I was guided by Rick Oleson's instructions.
http://forum.mflenses.com/backfocus-with-split-screen-t15582.html


Reply

This is front focussing by about 5m so it's gonna need a lot of shimming.


Reply

At what focal length and at what distance?

Here's a handy chart showing relationship between shim thickness and front/back focus: http://farm4.static.flickr.com/3354/4626297720_75252d6c29_o.png

Note that using the widest angle lens you have to calibrate focus screen is most accurate.


Reply

iangreenhalgh1 wrote:
This is front focussing by about 5m so it's gonna need a lot of shimming.

Is that all you've got to say? No "thanks for the advice"?


Reply

I spend 4 hrs with my 400d and was about to give up.
On the last try, i discover my mistake: the focus screen must be plan with the holder, not just click in. I installed it wrongly and had it slightly disalign.
Your distances seems like you have removed the metal spacer/shim, or flipped side, or something in the way. It should not be as much. The 'washers' have precise thickness. Unless you know exact which, go for a set.

and use many lenses to test/calibrate. wide open, at minimum focua distance first. start with a fast fifty, then medium tele and other.

image quality of my 400d and yours may not justify for the extra hrs.


Reply

hoanpham wrote:
[...]and use many lenses to test/calibrate. wide open, at minimum focua distance first. start with a fast fifty, then medium tele and other.[...]


That is good advice -- use fast fifty to get calibration close at first.

However, use fastest wide angle in native mount (Canon) lens to calibrate. When wide angle gives correct infinity focus, all other focal lengths will be most accurate. Because tolerances for wide angle is much less than for telephoto. Otherwise, telephoto may look accurate, while wide angle will not be accurate yet.