| View previous topic :: View next topic |
| Author |
Message |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Sat Oct 16, 2010 10:29 am Post subject: Opening the CZJ 200/2.8 |
|
 Posted: Sat Oct 16, 2010 10:29 am Post subject: Opening the CZJ 200/2.8 |
|
|
Anu wrote:
The winter is coming, thus the temperatures go down. It is now clear that I need to relube the helicoid of the CZJ 200mm lens. I plan to use white lithium grease which seems to work well, though I've not tried it for quite this use before.
Now, the question is, can anyone give me hints regarding the job itself? I've opened many other lenses, but never this one, and I want to avoid doing extra work, just the bare minimum for lubing as otherwise the lens is in splendid condition.
The front seems to be rather difficult to remove, maybe I should approach from the rear? Or maybe I can't access the helicoid from there?
What are the two screws on the side of the lens - the big one next to the 3 meter mark on the focusing ring, and the tiny one maybe 4-5cm up and 110-120 degrees to the right from it? |
|
| Back to top |
|
 |
Attila
 Joined: 24 Feb 2007 Posts: 58002
Expire: 2025-11-18
|
 Posted: Sun Oct 17, 2010 1:49 am Post subject: |
|
 Posted: Sun Oct 17, 2010 1:49 am Post subject: |
|
|
Attila wrote:
These was first lens what I did clean by myself , it was years ago. I don't remember either of details and difficulties. I think it has logical built you will open and re-lube easily. |
|
| Back to top |
|
 |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Sun Oct 17, 2010 6:32 am Post subject: |
|
 Posted: Sun Oct 17, 2010 6:32 am Post subject: |
|
|
Anu wrote:
| Attila wrote: |
| These was first lens what I did clean by myself , it was years ago. I don't remember either of details and difficulties. I think it has logical built you will open and re-lube easily. |
Thank you. One of the under appreciated nice things about the old CZJ lenses is the logical construction - in general easy to open and understand - fantastic feature for folks like us who use them decates after the best before date . With this particular lens there are some abnormalities from the normal that hit the eye - the two screws on the side of the barrel, and the lacking spanner wrench slots in the rings that sit on top of the front element. I have no clue how to open the lens from the front. I guess I'll try to enter from behind then (there's always been something loose inside, creating sound in the back, so I guess it's a good idea to have a look anyhow), but I'm going to wait a couple of days for more hints/tips. |
|
| Back to top |
|
 |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Mon Oct 18, 2010 1:08 pm Post subject: |
|
 Posted: Mon Oct 18, 2010 1:08 pm Post subject: |
|
|
Anu wrote:
Since I got little or no advice, I went ahead and opened the lens.
Attila was correct - this lens is not only logical, but also trivial to clean, when it comes to the focusing helicoid. There is no need to touch the front, just dive in from the back. The big screw on the side was indeed the screw that locks the focusing and removing it allows one to get full access.
Very neatly laid out and well protected internals - seems like they thought of protecting the internals from folks who need to grease the helicoind as only little is still visible to the eye.
The weird sound I had heard was just cause ball bearings hitting each other.
This copy, while it is very much used as the outside looks tell, is extremely clean inside. Clearly no amateur has opened the lens up until now
So, so far so good. I still need to grease it up and rebuild it. Should be easy, but one never knows... |
|
| Back to top |
|
 |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Mon Oct 18, 2010 3:29 pm Post subject: Done |
|
 Posted: Mon Oct 18, 2010 3:29 pm Post subject: Done |
|
|
Anu wrote:
In spite of the lens being trivial to open and trivial to close - there seems to be pretty much only one possible way to close it up with it working - I managed to spend over an hour fighting with it.
And I am not quite happy with the stiffness now. It's a bit too stiff, allright, but not quite there where I want it to be. I guess I need to take some lube off? Well, That'll have to wait for another day, as right now I'm doing the good old fridge-test: the lens is cooling inside the fridgerator until I can test how this grease works under cooler temperatures. |
|
| Back to top |
|
 |
Attila
 Joined: 24 Feb 2007 Posts: 58002
Expire: 2025-11-18
|
 Posted: Mon Oct 18, 2010 5:44 pm Post subject: |
|
 Posted: Mon Oct 18, 2010 5:44 pm Post subject: |
|
|
Attila wrote:
Fridge test is an excellent idea, I look forward your progress. |
|
| Back to top |
|
 |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Tue Oct 19, 2010 10:29 am Post subject: |
|
 Posted: Tue Oct 19, 2010 10:29 am Post subject: |
|
|
Anu wrote:
Re-opened, re-cleaned, re-lubed with less lube and this time rebuilding was trivial. I took plenty of photos, which will be posted later in a new thread.
Regarding the white-lithium, it is too sticky for this particular lens. It feels like it's stickier now that I put less grease than the first time, especially when in fridge-temperature (turning the focus unscrews the lens from the camera). I think I'll try it with more lubing next. And if/when that fails, I'll try something with lower viscosity - any ideas anyone? |
|
| Back to top |
|
 |
Attila
 Joined: 24 Feb 2007 Posts: 58002
Expire: 2025-11-18
|
 Posted: Tue Oct 19, 2010 4:45 pm Post subject: |
|
 Posted: Tue Oct 19, 2010 4:45 pm Post subject: |
|
|
Attila wrote:
| Anu wrote: |
Re-opened, re-cleaned, re-lubed with less lube and this time rebuilding was trivial. I took plenty of photos, which will be posted later in a new thread.
Regarding the white-lithium, it is too sticky for this particular lens. It feels like it's stickier now that I put less grease than the first time, especially when in fridge-temperature (turning the focus unscrews the lens from the camera). I think I'll try it with more lubing next. And if/when that fails, I'll try something with lower viscosity - any ideas anyone? |
Thanks ! I look forward your pictorial guide! |
|
| Back to top |
|
 |
martyn_bannister
 Joined: 23 May 2010 Posts: 1151
|
 Posted: Tue Oct 19, 2010 6:06 pm Post subject: |
|
 Posted: Tue Oct 19, 2010 6:06 pm Post subject: |
|
|
martyn_bannister wrote:
| Anu wrote: |
Re-opened, re-cleaned, re-lubed with less lube and this time rebuilding was trivial. I took plenty of photos, which will be posted later in a new thread.
Regarding the white-lithium, it is too sticky for this particular lens. It feels like it's stickier now that I put less grease than the first time, especially when in fridge-temperature (turning the focus unscrews the lens from the camera). I think I'll try it with more lubing next. And if/when that fails, I'll try something with lower viscosity - any ideas anyone? |
I think Lithium grease (dark grey in colour) has a temperature range from -70 to +120 C. I find that this works very well for me. I try not to use too much. |
|
| Back to top |
|
 |
Anu
 Joined: 14 Apr 2009 Posts: 879
|
 Posted: Tue Oct 19, 2010 6:14 pm Post subject: |
|
 Posted: Tue Oct 19, 2010 6:14 pm Post subject: |
|
|
Anu wrote:
| martyn_bannister wrote: |
| Anu wrote: |
Re-opened, re-cleaned, re-lubed with less lube and this time rebuilding was trivial. I took plenty of photos, which will be posted later in a new thread.
Regarding the white-lithium, it is too sticky for this particular lens. It feels like it's stickier now that I put less grease than the first time, especially when in fridge-temperature (turning the focus unscrews the lens from the camera). I think I'll try it with more lubing next. And if/when that fails, I'll try something with lower viscosity - any ideas anyone? |
I think Lithium grease (dark grey in colour) has a temperature range from -70 to +120 C. I find that this works very well for me. I try not to use too much. |
Do you use it with this lens? Different lenses require different grease for best operation. This particular one requires something that is rather low in viscosity. The white lithium I've tried, is a bit too thick. I will still probably try once more with even less of it (I already put ridicilously little, and even that made it stiff). I also have a couple of silicon greases I may try if they have better viscosity. |
|
| Back to top |
|
 |
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|